Rating: 4.5 / 5 (8735 votes)
Downloads: 28890
>>>CLICK HERE TO DOWNLOAD<<<
Din en pdf iso 898- 2, edition, february - fasteners - din en iso 898 2 pdf mechanical properties of fasteners made of carbon steel and alloy steel - part 2: nuts with specified property classes ( iso 898- 2: ) there is no abstract currently available for this document iso 898- 2 specification concludes mechanical and physical properties of nuts with coarse thread and fine pitch thread made of carbon steel and alloy steel when tested at an ambient temperature range of 10 ° c to 35 ° c. iso 898- 2: mechanical properties of fasteners made of carbon steel and alloy steel – part 2: nuts with specified property classes – coarse thread and fine pitch thread chemical composition as per iso 898- 2: for typical grades hardness requirement as per iso 898- 2: for typical grades pdf. this part of iso 898 specifies mechanical and physical properties of nuts with coarse thread and fine pitch thread made pdf of carbon steel and alloy steel when tested at an ambient temperature range of 10 ° c to 35 ° c. it is not applicable to set screws and similar threaded fasteners not under tensile stress ( see iso 898- 5). < p> din en iso 898 2 pdf pdf this part of iso 898 specifies mechanical and physical properties of nuts with coarse thread and. the european standard en iso 898- 2: has been prepared by iso/ tc 2 " fasteners" in collaboration with cen/ tc 185 " fasteners", the secretariats of which are held by din ( germany). it does not specify requirements for such properties as ⎯ weldability, ⎯ corrosion resistance, ⎯ resistance to shear stress,. din en isomechanical properties of fasteners made of carbon steel and alloy steel – part 2: nuts with specified property classes – coarse thread and fine pitch thread astm f606- 2 – standard test methods for determining the mechanical properties of externally and internally threaded pdf fasteners, washers, and rivets. this document does not specify requirements for functional properties such as: — prevailing torque properties ( see iso 2320), — torque/ clamp force properties ( see iso 16047 for test method), — weldability, or — corrosion resistance. part 2: nuts with specified property classes table din of contents figures tables equations parts available in: en fr redlines? mechanical properties of fasteners made of carbon steel and alloy steel?
mechanical properties. iso 898- 2: ( e) introduction iso 898, the basic standard for fasteners with iso metric thread made of carbon steel and alloy steel, was developed in several parts, and includes diameters 5 mm to 39 mm only for nuts. iso 898- 2, 4th edition, september - fasteners — mechanical properties of fasteners made of carbon steel and alloy steel — part 2: nuts with specified property classes this document specifies the mechanical and physical properties of nuts made of non- alloy steel or alloy steel, when tested at the ambient temperature range of 10 ° c to. for nuts designed for particular applications, see iso/ tr 16224. this document specifies the mechanical and physical properties of nuts made of non- alloy steel or alloy steel, when tested at the ambient temperature range of 10 ° c to 35 ° c. standard fasfeners, iso 898- 2 was sub- committee prepared by technical committee sc 1, mechanicai properfies of this ( iso second edition 898- 2: 1980), which cancels has been and replaces technicalty revised. the fit- st edition. nuts din en iso 898 2 pdf conforming to the requirements of din en iso 898 2 pdf this part of iso 898 are evaluated at that ambient temperature range. din en iso 898- 2. thin nuts, regular nuts & high nuts conforming to the requirements of iso 898- 2 are evaluated at that ambient.
iso 898 consists of the following parts, under the general title mechanical properties of fasteners made of carbon steel pdf and alloy steel: — part 1: bolts, screws and studs with specified property classes — coarse thread and fine pitch thread — part 2: nuts with specified property classes — coarse thread and fine pitch thread — part 5: set scr. an tnter- member bodies casting a vote. property classes are specified in the iso 898 series in relation to materials and mechanical properties, so that nuts in. this document applies to nuts: — with iso metric thread ( see iso 68- 1), — with diameter/ pitch combinations according to iso 261 and iso 262,. international standard cancelled. iso 898 consists of the following parts, under the general title mechanical properties of fasteners made of carbon steel and alloy steel :. part 2: pdf nuts with specified property classes coarse thread and fine pitch thread status : withdrawn this standard has been revised by iso 898- 2: abstract this part of iso 898 specifies mechanical and physical properties of nuts with coarse thread and fine pitch. every interested party, which is member of an organization based in luxembourg, can participate for free in the development of luxembourgish ( ilnas), european ( cen, cenelec) and international ( iso, iec) standards: participate in the design of standards foresee future developments participate in technical committee meetings. ilnas- en iso 898- 2:. this third edition cancels and replaces the second edition ( iso 898- 2: 1992) and iso 898- 6: 1994, which have been technically revised.
publication as an inte national standard requires approval by al least 75% of the member bodies casting a vole international standard iso 898- 2 was prepared by technical committee iso/ tc 2, fasteners, sub- committee sc 1, mechanical properties of fasteners. mechanical properties of fasteners made of carbon steel and alloy steel - part 2: nuts with specified property classes - coarse thread and fine pitch thread ( iso 898- 2: ) ; german version en iso 898- 2:. the responsible german standardization committee is working committee naaa " verbindungselemente mit metrischem innengewinde" ( " fasteners with metric. having thread tolerances in din en iso 898 2 pdf accordance with iso 965- 1, iso 965- 2 and iso 965- 4. historical version. iso 898- 2 scope. international iso/ tc 2, tasfeners. mechanical properties of fasteners made of carbon steel and alloy steel - part 2 : nuts with specified property classes - coarse thread and fine pitch thread.
iso 898- 2: ( en) fasteners? replaced standards ( 1) iso 898- 2:. this part of iso 898 applies to nuts made of carbon steel or alloy steel with coarse thread from m5to m39 and find pitch thread from 1 mm to 39 mm, with triangular iso metric thread according to iso 68- 1, with height of a least 0, 45d, with a minimum outside diameter or width across flats of at least 1, 45d, able to mate with bolts, screws and.
留言列表
